If the preset zero switches are used to set the initial value of wavenumber the result is the actual wavenumber. It is necessary to show the spot diagrams on two scales to relate the spot size to the entrance slit size and still show spot detail. The microscope alignment device contains a cross hair the center of which is the aiming point for precise stand alignment. This corresponds to a source size in a short range laboratory set-up of about O. The system halt is removed by pressing the reset button on the coupler front panel. It is illuminated by a light emitting diode LED mounted on the other side of the chopper housing so that the chopper blade passes between the LED and the photo diode. The data coupler in turn commands the D.

2go version 3.6.8

Uploader: Arashimuro
Date Added: 15 July 2009
File Size: 63.59 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 95961
Price: Free* [*Free Regsitration Required]

This process takes approximately 52 ms after which the printer releases the coupler which in turn enables versuon data con- trol pulse and the counter.

Free download 2go version 3 8

Closed cycle He refrigerator consisting of com- pressor and cold head connected by flexible hoses, Operating Temp. Aluminum was chosen for the stand material from consideration of weight and ease of evrsion. The centerline blade width is about 8. The clock pulses sequentially cause a record and increment of the digital tape recorder.

The dewar is attached to the refrigerator cold head. Double Diffraction A mar: Receiver Stand- Left Side 3.

2go version 3.6.8

Free Download Power2Go 8. The transformer provides voltage gain and matches the low im- pedance detector to the high input impedance of the preamplifier. Changes in the system after about 15 minutes take place quite slowly, and would therefore have less effect about twenty times less on calibration change during a run.


We also have minivans buses freight transport. The entrance slit of the monochromator defines the field of view of the receiver telescope.

Design and Construction of a System for Remote Optical Sensing of Emissions

There is one Irtran 2 window mounted on the dewar which contains the detector. The 30U stainless steel blade was made from a blank gear. The advantages of the digital tape as an output device are its speed and computer compatibility.

It will be found convenient, however, in the latter case to use a laboratory jack near the center of the frame. The components which are primarily mechanical are the stands, the auxiliary stands and the electronic enclosures.

In the emission mode of operation the signal output results from the difference between the source and reference beams. Although it would have been desirable to support the telescope on both ends this would have considerably extended the stand length which would have made manufac- turing difficult. Internal to the instrument power is required in three indirect formsj chopper drive, blackbody heater and D.

The system is designed to be easily transported for field use. Choose Download Locations for maxim — order a taxi v3. The wheels are widely spaced so that the assembly will be stable under any combination of component installation. In general, it is desirable to locate the apertures in that portion of the system common to both beams. Therefore, a periscope device which picks off a portion of the main beam has been provided for use in these situations.


2go version 3.6.8

Taking the telescope reflectance values as typical the reflectance values for the system may be obtained by raising the reflectance value for one surface to the 10th and 12th power. The size was chosen as 0. There are two flexible hoses connected between the c. This requires mounting the cooler on vibration isolation mounts a separate support was judged opera- tionally unacceptable and providing low transmission couplings for the vacuum jacket and the detector heat flow path.

Although this is a mechanical device its major function is optical and, therefore, will be des- cribed here. Also shown is the measured transmission of the field lens used at the monochromator entrance slit at 0.

Download Boomplay Android APK

The beam is turned by means of the flat diagonal mirror between the spherical mirror and the intermediate focus. A given component may appear in more than one section. As indicated in the optical diagram all of the elements of the reference optical system are sized so as not to limit the reference beam.

Ge detector in this mode has an amplitude proportional to the emission and a frequency equal to the reference chopper frequency.